Windows 11 Esxi - Revision history

Karavi at 10:29, 8 April 2025

2025-04-08T10:29:00Z

← Older revision		Revision as of 10:29, 8 April 2025
Line 7:		Line 7:
	Shift + F10		Shift + F10
	2. Type regedit and hit enter.		2. Type regedit and hit enter.
			regedit
	3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig		3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig
	HKEY_LOCAL_MACHINE\SYSTEM\Setup		HKEY_LOCAL_MACHINE\SYSTEM\Setup

Karavi at 10:28, 8 April 2025

2025-04-08T10:28:38Z

← Older revision		Revision as of 10:28, 8 April 2025
Line 5:		Line 5:

	1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt.		1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt.
			Shift + F10
	2. Type regedit and hit enter.		2. Type regedit and hit enter.

	3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig		3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig
			HKEY_LOCAL_MACHINE\SYSTEM\Setup
	4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1		4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1
			ByPassTPMCheck

Karavi at 10:25, 8 April 2025

2025-04-08T10:25:34Z

← Older revision		Revision as of 10:25, 8 April 2025
Line 15:		Line 15:

	Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the corner of the setup screen, the setup will start again and ignore the TPM requirements.		Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the corner of the setup screen, the setup will start again and ignore the TPM requirements.





			install Windows 11 without Internet or network

			In the installation phase

			ust press
			Shift+F10



			or like in my case
			Shift+Fn+F10



			to open Command Prompt and type
			OOBE\BYPASSNRO



			where the two OO:s are letters, not number zeros. Then, press
			Enter

Karavi at 09:56, 8 April 2025

2025-04-08T09:56:35Z

← Older revision		Revision as of 09:56, 8 April 2025
Line 5:		Line 5:

	1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt.		1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt.

	2. Type regedit and hit enter.		2. Type regedit and hit enter.

	3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig		3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig

	4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1		4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1



	Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the corner of the setup screen, the setup will start again and ignore the TPM requirements.		Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the corner of the setup screen, the setup will start again and ignore the TPM requirements.

Karavi: Created page with " on isntall : Time to work around the issue… 1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt. 2. Type regedit and hit enter. 3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig 4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1 Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the cor..."

2025-04-08T09:53:13Z

Created page with " on isntall : Time to work around the issue… 1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt. 2. Type regedit and hit enter. 3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig 4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1 Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the cor..."

New page

on isntall :
Time to work around the issue…

1. When you get the error picture above simply press Shift + F10 and this will bring up a dos prompt.
2. Type regedit and hit enter.
3. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\Setup and create a new Key called: LabConfig
4. Create inside the LabConfig Key a ByPassTPMCheck DWORD (32-bit) with the value of 1

Click OK after editing the value data and then close out of all of the screens. Once you click on the red x in the corner of the setup screen, the setup will start again and ignore the TPM requirements.